Reconditioned Machines and Systems

Reconditioned Machines & Systems

Just because it is used does not mean it is any less able to give you good service. When a machine first arrives in our Rushden based workshop it receives an in-depth assessment in many areas, including age, operation, mechanical condition, electrical condition, previous service history and future potential. Only then do we strip the unit down to its chassis and carry out a complete service but just as importantly all guarding and electrical control circuits are updated to meet and exceed the safety requirements laid down by the UK HSE, something that many dealers and end sellers do not and cannot complete or say.  This is because we take the time to check, to understand how the machine works and the application it needs to fullfill.

You will often see on dealer pages such things as exposed soft un-shrouded cables travelling around the machine and floor, would you want a cable to be easily trapped or damaged?, unlikely, we make sure all cables are channelled and where they have to be exposed for instance on a tray press then they are safely run inside earthed steel reinforced shrouding or conduits.  We understand the industry and world these machine go into, we know it is easy for a die or cutting board to be dropped or knocked against the machines.

UK Engineering Expertise

For more information on our extensive UK facilities including custom manufacture and reconditioning production lines. Please CLICK HERE

Reconditioning represents a cost effective alternative to replacing an old machine. Due to the robust nature of our machines we are able to replace worn parts and keep machines in circulation for extended periods of time. Reconditioning typically includes the replacement of all worn parts and the finished machine is normally capable of operating to the same degree of precision and reliability as when it first left the factory.

Our ability to provide a reconditioning service is a reflection of our size in the market place and large installed machine base, something that cannot easily be offered by some of our competitors. If you have a machine which has served you well over the years but now needs some TLC to bring it back to its best, call us today and find out how reconditioning can save you the capital expenditure of buying a new machine.

There are many advantages to purchasing a reconditioned machine from us as there IS NO other company in the UK with our experience or knowledge on soft material cutting equipment, and as we use genuine manufacturer’s parts you will NOT find a better reconditioned machine supplied by anyone else.

Machinery Wanted

Do you have a used Atom or Cutting Systems UK Ltd Machine that you would like to sell? 

Do you have a used ATOM or system supplied by us (Cutting Systems UK Ltd) that you are looking to sell? We are always looking to buy our machinery and systems back.

We can sell on your behalf if we know what is available and either keep the machine at your site until sold or move it into our storage facility to allow your space back.

We will oversee the entire project from decommissioning to shipping as per our normal machine moving and installation services.

For more information or to discuss the purchase of your machinery please call us on 01933 359359 or CONTACT US via email.

ATOM SE25CE Swing Beam Die Cutting Press

 

SOLD – but many other configurations often available

Fully reconditioned machine, including new oil, filters, complete electrical re-wire which meets all current safety regulations. Complete strip, base and top coat of industrial finished paint. Supplied with Natural Nylon cutting board and new aluminium cutting plate. Machine palletised ready for installation by ATOM UK service engineers or for dispatch to customer.

Cutting Head Size – 500 x 600mm
Cutting Bead – 1000 x 500mm
Cutting Power – 25tons

Supplied with Natural Nylon cutting board and new aluminium cutting plate. Machine palletised ready for installation by ATOM UK service engineers or for dispatch to customer.

For more information please CLICK HERE

Selection of Swing Beam ‘Clicker’ Cutting Presses

Produced by ATOM or Pedersen

Cutting Force: 8 – 25ton
Cutting Area: 600mm x 30mm – 1000mm x 500

For more information please CLICK HERE

ATOM S588 Travelling Head Press

Head Size: 500mm x 500mm
Bed Size: 1600mm x 500mm
Tonnage: 25tons

Fully Serviced

For more information or to book a viewing please CLICK HERE

ATOM S520 Travelling Head Press

Head Size: 750mm x 750mm
Bed Size: 2000mm x 750mm
Tonnage: 25tons

Fully Serviced

For more information or to book a viewing please CLICK HERE

ATOM S320 Beam Cutting Press

 

SOLD, 2 more available

Cutting Area: 1600mm x 400mm
Cutting Force: 20tons
Options: Feed Rollers

Completely Reconditioned Including Paintwork
Fully Serviced
New Cutting Board Supplied

For more information or to book a viewing please CLICK HERE

ATOM PL105 High Tonnage Tray Machine Cut & Embossing

Usable Area: 500mm x 400mm
Tonnage: 120tons

Fully Serviced

For more information or to book a viewing please CLICK HERE

ATOM PL500 High Tonnage Tray Machine Cut & Embossing

Usable Area: 350mm x 300mm
Tonnage: 45tons

Fully Serviced

For more information or to book a viewing please CLICK HERE

ATOM S658 Tray Beam Press

Cutting Area: 1600mm x 800mm
Tonnage: 50tons

Fully Serviced

For more information or to book a viewing please CLICK HERE

ATOM S530 CNC

Head Size: 500mm x 500mm
Cutting Area: 1600mm x 500mm
Tonnage: 25tons

Fully Serviced

For more information or to book a viewing please CLICK HERE

ATOM S735CN CNC Single Tool Automatic Cutting Press with Cutting Belt & ‘Pinch & Grab’

 

SOLD – 1 More Available

Cutting Area: 700mm x 700mm
Cutting Force: 30tons

Special power to cutting area ratio

Fully Serviced
New Cutting Belt

For more information or to book a viewing please CLICK HERE

ATOM 66110/2 BP Automatic ‘Pinch Grab’ Beam Cutting Press

SOLD – 1 More Available

Cutting Area: 2000mm x 1350mm
Cutting Force: 100tons

Special Size Cutting Area

Fully Serviced
New Cutting Belt Fitted

For more information or to book a viewing please CLICK HERE

KMT (Ingersol Rand) 30HO OEM SL-IV (Soft Seal End Cap) Waterjet Intensifier

30HP 3,800bar
Fully Serviced by Manufacturer Engineering Company (Cutting Systems UK Ltd)
Genuine Parts kept in stock
No pressure control for external tables or control systems
Can be supplied and electrically connected to many different makes and models of waterjet cutting tables, or by using a Siemens S7 PLC we can make it a stand alone with remote start stop etc.
Can be supplied as a complete system, with external booster pump, water softener and water storage tank, also heaters if needed. Please see custom WaterJet page

For more information or to book a viewing please CLICK HERE

we do not always recondition a machine until it is sold because;

  • you may want customised guarding
  • you may want customised automated loading and unloading systems, powered die rails, pip suction system fitting etc
  • we do not want the paint work to be damaged whilst the machine is in our storage unit
  • to ensure it meets the latest HSE safety legislation we re-wire each machine on its own specifications to the HSE requirements that week.
  • lubricants such as grease can thicken, ‘go off’ and become ineffective and a problem when not used.

….. our range may be smaller than others, but the machines we sell we understand them, their application and their world in a depth no body else in the UK does or wants to.

*All of the pictures shown above are for illustration purposes only, as finished machines may vary from that shown in the exact model, pictured size and some specifications.

Address

 
Units 25 & 29 Francis Court
Norris Way
Rushden Northants
NN10 6AY
 
TEL: +44 (0)1933 359359
 
FAX: +44 (0)1933 359399